Pressure Switch Selection Guide

How to specify an air, water or differential pressure switch: set point, differential, electrical rating, media, connection and approvals.

A pressure switch is an electromechanical device that opens or closes an electrical contact when the pressure of a gas or liquid reaches a preset set point. Getting the specification right is what separates a reliable safety interlock from a part that causes nuisance faults. This guide covers the parameters engineers normally agree before a sample is built.

The six parameters that define a pressure switch

Parameter What to specify Typical Regal options
Media Air, flue gas, water or another liquid Air, water and differential versions; diaphragm material matched to the media
Set point Pressure at which the contact changes state Differential from about 20 Pa; water 5-200 kPa; level 10-500 mm water column
Differential Gap between cut-in and cut-out Fixed or adjustable, selected for the pump or fan duty cycle
Electrical rating Voltage, current and load type Contacts rated for appliance and industrial control loads
Connection Hose barb, thread, terminal type and orientation Custom connectors, terminals and mounting brackets
Environment Temperature, humidity, vibration and IP protection Sealed housings and high-temperature diaphragms

Air, water and differential pressure switches compared

Type Media Typical function Common applications
Air pressure switch Air or flue gas Proves fan airflow before ignition Gas boilers, wall-hung boilers, furnaces, water heaters
Differential pressure switch Air Monitors the pressure difference across a filter or fan HVAC air handling units, ventilation systems
Water pressure switch Water Starts or stops a pump at set points Booster pumps, water heaters, purifiers
Water level switch Air pressure from a water column Controls fill level Washing machines, dishwashers, water tanks

How to set cut-in and cut-out points

For a pump that should start at 2 bar and stop at 3 bar, the cut-in point is 2 bar and the cut-out point is 3 bar, giving a 1 bar differential. A wider differential means fewer starts per hour and longer motor life; a narrower differential holds pressure more tightly. Always confirm that the maximum surge pressure stays below the switch proof pressure.

For a boiler fan, the switch normally proves a small negative or positive pressure at the flue. The set point is chosen so normal fan operation keeps the switch made, while a blocked flue, failed fan or disconnected sensing tube drops the pressure enough to open the contact and lock out ignition.

Common selection mistakes

  • Choosing a range that puts the set point at the very bottom of the scale, where accuracy is poorest.
  • Ignoring the differential, then finding the pump short-cycles.
  • Using an air-rated switch on a water line without checking diaphragm compatibility.
  • Forgetting connector orientation and mounting space inside the appliance.
  • Specifying certifications after the design is frozen instead of at the start.

When a flow sensor or level switch is the better choice

If the question is “is water moving?” rather than “is pressure present?”, a flow sensor gives a signal proportional to flow and is used for burner modulation in water heaters and boilers. If the question is “how full is the tank?”, a water level switch or capteur de niveau d'eau senses the air pressure created by the water column and is used in washing machines and dishwashers.

Frequently asked questions

What is a pressure switch?

A pressure switch is an electromechanical device that opens or closes an electrical contact when the pressure of a gas or liquid reaches a preset set point. It is used for safety interlocks, pump control and level detection in boilers, water heaters, compressors and household appliances.

Should I choose an air pressure switch or a water pressure switch?

Choose an air (differential) pressure switch when the media is gas or air and the measurement is a small pressure difference, such as proving fan airflow in a boiler. Choose a water pressure switch when the media is liquid and the switch must start or stop a pump; the diaphragm and wetted parts must be compatible with the water.

What set point range do I need?

Specify the normal working pressure, the cut-in point, the cut-out point and the maximum surge pressure. Regal air pressure switches cover differential ranges from roughly 20 Pa upward, water pressure switches cover 5-200 kPa, and water level switches cover 10-500 mm water column. Custom ranges are available.

What is differential and why does it matter?

Differential is the difference between the cut-in and cut-out pressures. A wider differential reduces switching frequency and protects pumps and fans; a narrower differential gives tighter control but more cycles. Match the differential to the duty cycle of the pump, fan or burner.

Ready to specify a part? Send the media, set point, differential, connection and annual volume to our engineers through the contact form, or browse the air pressure switch, water pressure switch et safety relief valve ranges.

WhatsApp